Mbps vs MB/s: Why Downloads Seem Slower
Why a 300 Mbps plan downloads at about 37.5 MB/s: bits vs bytes, the divide-by-8 rule, protocol overhead, MB vs MiB, and how to estimate download times.
Short answer
Internet plans are sold in megabits per second (Mbps), while download windows show megabytes per second (MB/s), and one byte is eight bits. Divide the Mbps figure by 8 to get MB/s, so a 300 Mbps connection tops out around 37.5 MB/s before overhead.
Key takeaways
- A lowercase b means bits and an uppercase B means bytes; 8 bits make 1 byte.
- Network protocol headers take roughly 5 percent of each standard Ethernet frame, so real transfer rates land a little below the divide-by-8 figure.
- Operating systems may report sizes in binary units (MiB, GiB), which makes a 50 GB file look like about 46.6 in Windows.
You pay for a 300 Mbps internet plan, start a large download, and the progress bar says 36 MB/s. Nothing is broken. Internet speeds and file sizes are measured in different units, and the gap between them is a factor of eight before any other effect kicks in. This explainer shows the conversion, the smaller losses on top of it, and how to estimate download times.
What is the difference between Mbps and MB/s?
Mbps counts megabits per second and MB/s counts megabytes per second, and a byte is eight bits, so the same speed is eight times larger in Mbps.
The capitalization carries the meaning. A lowercase "b" is a bit, the smallest unit of data. An uppercase "B" is a byte, a group of 8 bits. Network equipment and internet providers measure in bits per second because data moves over wires and radio one bit at a time. Storage and file sizes use bytes, so download windows, browsers, and game launchers show MB/s.
| Plan speed | Divide by 8 | Theoretical MB/s |
|---|---|---|
| 50 Mbps | 50 / 8 | 6.25 MB/s |
| 100 Mbps | 100 / 8 | 12.5 MB/s |
| 300 Mbps | 300 / 8 | 37.5 MB/s |
| 500 Mbps | 500 / 8 | 62.5 MB/s |
| 1 Gbps (1,000 Mbps) | 1,000 / 8 | 125 MB/s |
| 2 Gbps (2,000 Mbps) | 2,000 / 8 | 250 MB/s |
How do you convert Mbps to MB/s?
Divide the Mbps figure by 8 to get MB/s, and multiply MB/s by 8 to go the other way.
Worked example: a 300 Mbps plan gives 300 / 8 = 37.5 MB/s at most. Going the other direction, if a download runs at 20 MB/s, the connection is delivering 20 x 8 = 160 Mbps.
The data size and speed converter does these conversions and the download-time math below in your browser, including the binary units covered later in this post.
Why are real downloads slower than the math?
Every packet carries addressing and control headers that are not part of your file, so a few percent of the line rate is spent on overhead even on a perfect connection.
On a standard Ethernet network, each frame can carry up to 1,500 bytes of IP data. TCP and IP headers take at least 40 of those bytes, leaving 1,460 for your file. The frame itself adds another 38 bytes on the wire (header, checksum, preamble, and the gap between frames). That makes 1,460 useful bytes out of 1,538 sent, about 95 percent efficiency.
Applied to a gigabit line: 125 MB/s x 0.95 is about 118 MB/s, which matches the top speeds people see on wired gigabit connections. Other limits often matter more than overhead:
- The server or content network may cap speed per download.
- Wi-Fi throughput drops with distance, walls, and congestion; see Wi-Fi 7 explained for what newer standards change.
- Slow storage, such as an older hard drive, can fail to keep up with fast connections.
- Other devices on your network share the same bandwidth.
How long will a download take?
Download time equals file size in megabytes divided by speed in MB/s, so convert the plan speed first and then divide.
Worked example for a 50 GB game on a 300 Mbps plan:
- Convert the file to megabytes: 50 GB x 1,000 = 50,000 MB.
- Convert the speed: 300 Mbps / 8 = 37.5 MB/s.
- Divide: 50,000 / 37.5 = about 1,333 seconds.
- Convert to minutes: 1,333 / 60 = about 22 minutes.
That is the best case. At 95 percent efficiency it becomes about 23.4 minutes, and server limits or Wi-Fi conditions can stretch it further. The same file on a 100 Mbps plan (12.5 MB/s) takes about 4,000 seconds, a little over an hour.
What is the difference between MB and MiB?
A megabyte (MB) is 1,000,000 bytes, while a mebibyte (MiB) is 1,048,576 bytes, and some software uses the binary value but still labels it MB.
The binary prefixes (KiB, MiB, GiB, TiB) were introduced by the International Electrotechnical Commission so that powers of 1,024 would have their own names, as NIST explains on its reference page for binary multiples. In practice:
| Unit | Bytes |
|---|---|
| 1 MB (megabyte) | 1,000,000 |
| 1 MiB (mebibyte) | 1,048,576 |
| 1 GB (gigabyte) | 1,000,000,000 |
| 1 GiB (gibibyte) | 1,073,741,824 |
| 1 TB (terabyte) | 1,000,000,000,000 |
| 1 TiB (tebibyte) | 1,099,511,627,776 |
Drive makers and network speeds use decimal units. Windows File Explorer calculates sizes in binary units but labels them GB, so a 1 TB drive appears as about 931 GB and a 50 GB download as about 46.6 GB. macOS has used decimal units in Finder since Mac OS X 10.6, so the same drive shows close to 1 TB there.
None of this changes how much data you actually have. If a drive or file looks smaller than advertised, check which unit the software uses before assuming something went missing. And if free space really is running out, how to free up storage space covers where to look first.
Frequently asked questions
How many MB/s is 1 Gbps?
1 Gbps is 1,000 Mbps, which divided by 8 gives 125 MB/s. After Ethernet and TCP/IP overhead, the practical ceiling is roughly 118 MB/s on a wired gigabit link.
How long does a 50 GB download take on a 300 Mbps connection?
At the theoretical 37.5 MB/s, 50,000 MB takes about 1,333 seconds, or 22 minutes. Allowing for overhead and server limits, plan on 25 minutes or more.
Why does Windows show my 1 TB drive as 931 GB?
Drive makers count 1 TB as 1,000,000,000,000 bytes. Windows divides by 1,073,741,824 (a binary gigabyte, or GiB) but still labels the result GB, which gives about 931.
Is a speed test result in Mbps or MB/s?
Nearly all internet speed tests report Mbps, the same unit your provider uses. Download managers, browsers, and game launchers usually show MB/s.
Sources
Research-based: Technorat does not claim hands-on testing. See how we research. Spotted an error? contact@technorat.com